Nitrogen carrier gas for the separation of trace explosives on CI-GC/MS.

Fluctuations in ultra high purity (UHP) helium supply has the potential to negatively impact critical research efforts. Disruptions have increased significantly with suppliers prioritizing delivery to medical facilities. Due to the greater demand for helium, supply issues are likely to continue through the coming years. Many gas chromatography (GC)-based analytical methods rely on the supply of UHP helium, including those developed for the quantification of trace explosives. Vapor validation is critical in establishing sensor performance, limits of detection, and instrument performance. An alternate carrier gas must be established to maintain these critical functionalities. To circumvent the UHP helium disruptions, UHP nitrogen was explored as a replacement carrier gas in negative mode chemical ionization-gas chromatography/mass spectrometry (CI-GC/MS). Although, hydrogen is considered an acceptable alternative to helium in most GC-based separations, its' use as a replacement was omitted due to reactivity resulting in degradation of the CI-MS detector and incompatibility with the programmable temperature vaporization inlet on the GC used in this work. Herein discusses the method development of nitrogen carrier gas in the separation of an explosives mixture. Adjustments in flow rate, initial oven temperature, and ramp rate were made to achieve comparable analysis to that of helium. By lowering the flow rate and initial oven temperature peak resolution and sensitivity increased when using nitrogen carrier gas. Development of this method allows for continual laboratory output in times of helium scarcity.

Tailoring Amphiphilic Copolymers for Improved Aqueous Foam Stability.

Amphiphilic copolymers of various-molecular-weight (MW) poly(ethylene glycol) (PEG) were synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization. The first PEG series, poly(ethylene glycol)monomethacrylate (PEGMA, average Mn 200 and 400 MW), contained an -OH terminal group, and the second series, poly(ethylene glycol) monomethyl ether monomethacrylate (PEGMMA, average Mn 200, 400, and 1000 MW), possessed an -OCH3 terminal group. A total of five PEG-functionalized copolymers contained the same hydrophobic monomer, butyl acrylate (BA), and were successfully reproduced via a one-pot synthesis. The resulting PEG-functionalized copolymers provide a systematic trend of properties including surface tension, critical micelle concentration (CMC), cloud point (CP), and foam lifetime based on the average MW of the PEG monomer and final polymer properties. In general, the PEGMA series produced more stable foams with PEGMA200 demonstrating the least change in foam height with time over a 10 min period. The important exception is that at elevated temperatures, the PEGMMA1000 copolymer had longer foam lifetimes. The self-assembling copolymers were characterized by gel permeation chromatography (GPC), 1H nuclear magnetic resonance (NMR), attenuated total reflection Fourier transform infrared (FTIR-ATR), CMC, surface tension, dynamic light scattering (DLS), as a foam using a dynamic foam analyzer (DFA), and foam lifetime at ambient and elevated temperatures. The copolymers described highlight the importance of the PEG monomer MW and terminal end group for surface interaction and final polymer properties for foam stabilization.

Opioid cutting agents for use as internal standards in ion mobility spectrometry (IMS).

Opioids have become a serious public health concern over the last decade. These compounds are commonly found mixed, or cut, with safer compounds to make the opioids appear unadulterated while also enhancing the psychoactive effect on the user. Commercial benchtop and handheld IMS devices are capable of detection but published reduced ion mobility (K0) values, used to identify the target analytes with IMS instrumentation, have shown variability. This lack of agreement, even for compounds used for calibration, is often due to the effects of drift tube temperature, drift gas water vapor levels and the use in-house built instrumentation rather than commercial equipment. Multiple reports exist on assessment of IMS reference standards but a single, consensus universal standard does not exist. Assessment of opioid cutting agents as internal standards is a worthwhile pursuit if precise and accurate K0 values are obtained. The effects of drift gas water vapor content and drift tube temperature were used to evaluate the cutting agents. The K0 values of papaverine, a representative opioid with a similar K0 value to heroin and fentanyl, were calculated with respect to quinine and were in agreement with literature data. The use of quinine as an internal standard also improved precision relative to the instrument standard and shows promise in the application presented here.

Copolymer Reversible Addition-Fragmentation Chain Transfer Synthesis of Polyethylene Glycol (PEG) Functionalized with Hydrophobic Acrylates: A Study of Surface and Foam Properties.

A series of amphiphilic statistical copolymers involving poly(ethylene glycol) monomethacrylate (PEGMA, -OH terminated, average Mn 200 molecular weight) and various hydrophobic acrylates were synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization. The gradient copolymers were characterized by gel-permeation chromatography (GPC), 1H nuclear magnetic resonance (NMR), and attenuated total reflection Fourier transform infrared spectroscopy (FTIR-ATR). Solution properties of the copolymers were investigated utilizing surface tension measurement, dynamic light-scattering (DLS), as well as foam analysis using a dynamic foam analyzer (DFA). The PEG-functionalized copolymers showed a systematic trend depending on the hydrophobic moiety in properties including surface tension, critical micelle concentration (CMC), foam lifetime, and liquid drainage from the foam. Copolymers with alkyl-acrylates exhibited the best foam lifetime, demonstrating that the choice of hydrophobic moiety is crucial for foam stability. The PEG-functionalized materials described are considered promising additives for foam-stability purposes.

Empirical determination of explosive vapor transport efficiencies.

The transport efficiency of 2,4-dinitrotoluene (2,4-DNT), 2,4,6-trinitrotoluene (TNT) and 1,3,5-trinitro-1,3,5-triazinane (RDX) trace vapors through tubing materials that commonly constitute vapor handling infrastructures have been determined for a variety of tubing dimensions and sampling conditions. Using a programmable temperature vaporization inlet coupled with a gas chromatography mass spectrometer (PTV-GC-MS), the explosive vapors were quantified both with and without a length of tubing of a specific material in the sampling flow path. At vapor temperatures of 30 °C and 66 °C, minimal attenuations were observed for 2,4-DNT and TNT vapor concentrations when the tubing material was in-line with the sampling flow path, indicating that the transport is largely unaffected by interactions with the surface of the tubing materials. In contrast, RDX vapors showed large attenuations as a function of both sampling conditions and tubing materials/dimensions. For those experiments where attenuated RDX vapor transport was observed, the mass sequestered by interactions between the flowing vapor and the internal tubing surface was determined to be in the range of tens to hundreds of picograms. Of all the materials examined for RDX transport, fluorinated ethylene propylene (FEP) tubing resulted in the least amount of mass loss to surface interactions, with vapor transport efficiencies (VTEs) between 95-100%. However, for some materials, the combination of tubing dimensions and sampling conditions resulted in no RDX transport, even after sampling more than 250.0 L of vapor through the tubing.

Trace vapor generator for Explosives and Narcotics (TV-Gen).

The Trace Vapor Generator for Explosives and Narcotics (TV-Gen) is a portable and compact instrument designed to deliver a continuous source of trace-level vapors and vapor mixtures. It provides a tool to assist in the independent validation and verification of new materials and sensors under development for the vapor detection of explosives and narcotics. The design was conceived for use with a broad range of analytes, detection systems, materials, and sensors and to switch easily between the clean and analyte vapor streams. The TV-Gen system utilizes nebulization of aqueous analyte solutions, an oven to promote efficient transport, and a control box that provides dedicated computer control with logging capabilities. Resultant vapor streams are stable over several hours, with the vapor concentration controlled by a combination of aqueous analyte solution concentration, liquid flow rate through the nebulizer, and volume flow rate of air through the TV-Gen manifold.

Non-target analysis of vapor mixtures using silicon nanowire array sampling and thermal desorption.

This work presents and evaluates an algorithmic approach to deconvolving the elution profiles of chemical components of vapor mixtures that have been sampled and desorbed from a novel preconcentrator based on highly ordered silicon nanowire arrays. The arrays provide a medium for both preconcentration and partial chromatographic resolution, which is then further leveraged with multichannel detection. Here, mixtures of nitro aromatic vapors are sampled and then thermally desorbed from the device, at which point they are detected by a conventional mass selective detector. The overlapping elution profiles observed from the array are sequentially extracted using a chemometric analysis approach based on evolving factor analysis and multivariate curve resolution by alternating least squares, enabling qualitative and quantitative analysis of individual components without target analyte libraries or complete chromatographic separation. This work examines the analytical capabilities conferred to multichannel detection by silicon nanowire array pre-concentration and partial separation and discusses the technique's limitations, illustrated by both experimental and simulated data.

Combined secondary electrospray and corona discharge ionization (SECDI) for improved detection of explosive vapors using drift tube ion mobility spectrometry.

Secondary electrospray corona discharge ionization (SECDI) combines the principles of secondary electrospray ionization (SESI) and corona discharge (CD) to achieve higher sensitivity, which is demonstrated through the detection of 2,4,6-trinitrotoluene (TNT) and 2,6-dinitrotoluene (2,6-DNT) vapors using ion mobility spectrometry (IMS). Using SECDI, enhancements in the IMS signal for TNT and 2,6-DNT vapors at trace concentrations are as much as 2-26 times that observed with CD or SESI alone. The enhancement in sensitivity is hypothesized to result from an increase in ionization efficiency driven by a higher number of reactant ions associated with SECDI compared to either technique individually. The ability of SECDI to achieve higher sensitivity without the aid of dopant molecules demonstrates its merit as an alternative ionization technique.

Flow-Through Optical Chromatography in Combination with Confocal Raman Microspectroscopy: A Novel Label-Free Approach To Detect Responses of Live Macrophages to Environmental Stimuli.

Flow-through optical chromatography (FT-OC), an advanced mode of optical chromatography, achieved baseline separation of a mixture of silica microparticles (SiO2, 1.00 and 2.50 µm) and a mixture of polystyrene microparticles (PS, 1.00, 2.00, and 3.00 µm) based on particle size. Comparisons made between experimentally determined velocities for the microparticles and theoretically derived velocities from Mie theory and Stokes' law validated the data collection setup and the data analysis for FT-OC. A population shift in live macrophages (cell line IC-21, ATCC TIB-186) responding to environmental stimuli was sensitively detected by FT-OC. The average velocity of macrophages stressed by nutritional deprivation was decreased considerably together with a small but statistically significant increase in cell size. Mie scattering calculations demonstrated that the small increase in cell size of macrophages stressed by nutritional deprivation was not entirely responsible for this decrease. Confocal fluorescence microscopy and atomic force microscopy (AFM) studies revealed morphological changes of macrophages induced by nutritional deprivation, and these changes were more likely responsible for the decrease in average velocity detected by FT-OC. Confocal Raman microspectroscopy was used to shed light upon biochemical transformations of macrophages suffering from nutritional deprivation.

Part per quadrillion quantitation of pentaerythritol tetranitrate vapor using online sampling gas chromatography-mass spectrometry.

The development of an online sampling method using programmable temperature vaporization gas chromatography with a mass spectrometer detector (PTV-GC/MS) for the analysis of trace pentaerythritol tetranitrate (PETN) vapor is presented. PETN degradation was minimized by optimizing the temperature and flow rates of the vapor sampling infrastructure. Validation of the online method was done using a previously published technique, vapor sampling with Tenax-TA thermal desorption tubes followed by analysis with a thermal desorption system coupled to a programmable temperature vaporization gas chromatograph with a micro-electron capture detector (TDS-PTV-GC/µECD). Trace PETN vapor was generated using state-of-the-art instrumentation known as the TESTbed, located at the US Naval Research Laboratory. For PETN vapor concentrations in the parts per trillionvolume (pptv) range, quantitative results from the TDS-PTV-GC/µECD consistently showed concentrations approximately double that measured by the online PTV-GC/MS method, indicating that sample loss due to additional exposure to the vapor sampling infrastructure occurs when using online sampling. Further utilization of the online PTV-GC/MS system allowed for the quantitation/semi-quantitation of PETN vapor concentrations as low as 260 parts per quadrillionvolume (ppqv) with only 10 min of sampling time.

Silicon nanowire arrays for the preconcentration and separation of trace explosives vapors.

Silicon nanowire (SiNW) arrays are demonstrated as a suitable platform for the preconcentration of trace nitroaromatic compounds and subsequent desorption via Joule heating of the array. Arrays are fabricated from Si wafers containing an epitaxially grown layer of low conductivity intrinsic Si sandwiched between layers of high conductivity p-type Si. Passage of current through the nanowires results in nanowire temperatures in excess of 200 °C during heating of the arrays as verified by using the temperature-dependent shift of the Si Raman band at ˜520 cm-1. Analyte vapor preconcentration and partial separation is achieved on the array at analyte concentrations nearly two orders-of-magnitude below saturated vapor concentrations at room temperature. The effects of desorption carrier gas flow rate and temperature on the ability to preconcentrate and resolve the analytes of interest are determined. 2,6-dinitrotoluene (2,6-DNT) and 2,4-dinitrotoluene (2,4-DNT) were detected at nominal vapor concentrations of 800 pptv with a 1 min sample time (1.1 ng nominal mass load) and trinitrotoluene (TNT) was detected at a nominal vapor concentration of 65 pptv with a 10 min sample time (1.1 ng nominal mass load).

Micellar Electrokinetic Chromatography.

Micellar electrokinetic chromatography (MEKC) is a mode of capillary electrophoresis that allows for the separation of neutral molecules in an electric field. Typically, neutral molecules move with electroosmotic flow (EOF) or bulk flow during electrophoretic separations resulting in no temporal resolution between mixtures of neutral analytes. Inclusion of surfactant micelles in the separation buffer allows for the separation of neutral analytes from one another through association with the micelle. Here we outline the implementation of MEKC for the separation of neutral molecules using a mixture of nitroaromatic explosives and their degradation products serving as a test analyte mixture.

Mixed Vapor Generation Device for delivery of homemade explosives vapor plumes.

While there is a large body of research on the properties and detection of traditional military high explosives and propellant low explosives, there is a dearth of research on homemade explosive (HME) materials, though they are prevalent today. The safety of working with these materials in the laboratory is the greatest limiting factor preventing HME research. A vapor delivery tool, the Mixed Vapor Generation Device (MV-Gen), was designed to safely contain the individual solid or liquid components that often compose homemade explosives vapor plumes and deliver the mixed component vapors for instrumental sampling and analysis. Within the MV-Gen, each component is separated and only the vapors mix as they are carried through the device by flowing air. The resulting mixed vapor is representative of either mixed explosive material or bulk explosives. Component materials are held in up to four individual, removable vials with vapor concentrations controlled by vial orifice size, temperature, and diluent airflow. The total concentration can be adjusted by altering vial temperature via a thermal water jacket surrounding the entirety of the device, or by adjusting the flow rate of diluent air through the device. The MV-Gen was evaluated first with surrogate compounds, followed by two types of homemade explosives, to include a binary explosive mixture and a peroxide explosive. To evaluate the device, vapors were cold-trapped on an online sampling system and analyzed by gas chromatography/mass spectrometry. It was determined that the device yielded reproducible vapor concentrations of both single and mixed components, and the ratio of these vapors can be easily adjusted to mimic varying forms of homemade explosives.

Preconcentration and partial separation of nitroaromatic vapors using a methyltrimethoxysilane-based sol-gel.

Typical trace vapor analysis involves sorbent trapping, followed by desorption and chromatographic separation. This communication describes a method for streamlining this process by combining sorbent sampling/preconcentration with partial separation achieved through temperature-programmed thermal desorption. A novel sorbent trap was formulated in which tubular glass liners for a programmable-temperature gas chromatograph inlet were coated with a sol-gel based polymer stationary phase synthesized from methyltrimethoxysilane precursor and installed into the inlet, which was directly connected to a mass-selective detector by a fused silica capillary transfer line. This method is shown to achieve partial separation of two nitroaromatic vapors in a total 3-5min analysis time, which represents a tenfold improvement in speed in terms of the overall cycle time compared to an analogous conventional vapor analysis method. Both analytes proved to have a high dynamic range and loading capacity, with nitrobenzene achieving both high and low sampling extremes (0.32ng-4µg sampling concentration) with only a slight compromise in peak broadening. The multivariate curve resolution by alternating least squares algorithm (MCR-ALS) was shown to successfully resolve the overlapped elution profiles of the two nitroaromatic test vapors examined in this study.

Trace explosives sensor testbed (TESTbed).

A novel vapor delivery testbed, referred to as the Trace Explosives Sensor Testbed, or TESTbed, is demonstrated that is amenable to both high- and low-volatility explosives vapors including nitromethane, nitroglycerine, ethylene glycol dinitrate, triacetone triperoxide, 2,4,6-trinitrotoluene, pentaerythritol tetranitrate, and hexahydro-1,3,5-trinitro-1,3,5-triazine. The TESTbed incorporates a six-port dual-line manifold system allowing for rapid actuation between a dedicated clean air source and a trace explosives vapor source. Explosives and explosives-related vapors can be sourced through a number of means including gas cylinders, permeation tube ovens, dynamic headspace chambers, and a Pneumatically Modulated Liquid Delivery System coupled to a perfluoroalkoxy total-consumption microflow nebulizer. Key features of the TESTbed include continuous and pulseless control of trace vapor concentrations with wide dynamic range of concentration generation, six sampling ports with reproducible vapor profile outputs, limited low-volatility explosives adsorption to the manifold surface, temperature and humidity control of the vapor stream, and a graphical user interface for system operation and testing protocol implementation.

Isobutane Made Practical as a Reagent Gas for Chemical Ionization Mass Spectrometry.

As a reagent gas for positive- and negative-mode chemical ionization mass spectrometry (CI-MS), isobutane (i-C4H10) produces superior analyte signal abundance to methane. Isobutane has never been widely adopted for CI-MS because it fouls the ion source more rapidly and produces positive CI spectra that are more strongly dependent on reagent gas pressure compared with methane. Isobutane was diluted to various concentrations in argon for use as a reagent gas with an unmodified commercial gas chromatograph-mass spectrometer. Analyte spectra were directly compared using methane, isobutane, and isobutane/argon mixtures. A mixture of 10% i-C4H10 in argon produced twice the positive-mode analyte signal of methane, equal to pure isobutane, and reduced spectral dependence on reagent gas pressure. Electron capture negative chemical ionization using 1% i-C4H10 in argon tripled analyte signal compared with methane and was reproducible, unlike pure isobutane. The operative lifetime of the ion source using isobutane/argon mixtures was extended exponentially compared with pure isobutane, producing stable and reproducible CI signal throughout. By diluting the reagent gas in an inert buffer gas, isobutane CI-MS experiments were made as practical to use as methane CI-MS experiments but with superior analytical performance. Graphical Abstract ᅟ.

Trace Explosives Vapor Generation and Quantitation at Parts per Quadrillion Concentrations.

The generation of trace 2,4,6-trinitrotoluene (TNT), cyclotrimethylenetrinitramine (RDX), and pentaerythritol tetranitrate (PETN) vapors using a pneumatically modulated liquid delivery system (PMLDS) coupled to a polytetrafluoroethylene (PTFE) total-consumption micronebulizer is presented. The vapor generator operates in a continuous manner with final vapor concentrations proportional to the explosive concentration in aqueous solution delivered through the nebulizer and the diluent air flow rate. For quantitation of concentrations in the parts per billionvolume (ppbv) to parts per trillionvolume (pptrv) range, Tenax-TA thermal desorption tubes were used for vapor collection with subsequent analysis on a thermal-desorption system programmable-temperature vaporization gas chromatograph (TDS-PTV-GC) with a µ-ECD detector. With 30 min sample times and an average sampling rate of 100 mL min(-1), vapor concentrations of 38 pptrv for TNT, 25 pptrv for RDX, and 26 pptrv for PETN were determined. For parts per quadrillionvolume (ppqv) vapor quantitation of TNT and RDX, an online PTV-GC system with a negative-ion chemical ionization mass spectrometer (methane reagent gas) was used for direct sampling and capture of the vapor on the PTV inlet. Vapor concentrations as low as 160 ppqv and 710 ppqv for TNT and RDX were quantified, respectively, with an instrument duty cycle as low as 4 min.

Minimizing thermal degradation in gas chromatographic quantitation of pentaerythritol tetranitrate.

An analytical method for establishing calibration curves for the quantitation of pentaerythriol tetranitrate (PETN) from sorbent-filled thermal desorption tubes by gas chromatography with electron capture detection (TDS-GC-ECD) was developed. As PETN has been demonstrated to thermally degrade under typical GC instrument conditions, peaks corresponding to both PETN degradants and molecular PETN are observed. The retention time corresponding to intact PETN was verified by high-resolution mass spectrometry with a flowing atmospheric pressure afterglow (FAPA) ionization source, which enabled soft ionization of intact PETN eluting the GC and subsequent accurate-mass identification. The GC separation parameters were transferred to a conventional GC-ECD instrument where analytical method-induced PETN degradation was further characterized and minimized. A method calibration curve was established by direct liquid deposition of PETN standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Two local, linear relationships between detector response and PETN concentration were observed, with a total dynamic range of 0.25-25ng.

Quantitative detection of trace explosive vapors by programmed temperature desorption gas chromatography-electron capture detector.

The direct liquid deposition of solution standards onto sorbent-filled thermal desorption tubes is used for the quantitative analysis of trace explosive vapor samples. The direct liquid deposition method yields a higher fidelity between the analysis of vapor samples and the analysis of solution standards than using separate injection methods for vapors and solutions, i.e., samples collected on vapor collection tubes and standards prepared in solution vials. Additionally, the method can account for instrumentation losses, which makes it ideal for minimizing variability and quantitative trace chemical detection. Gas chromatography with an electron capture detector is an instrumentation configuration sensitive to nitro-energetics, such as TNT and RDX, due to their relatively high electron affinity. However, vapor quantitation of these compounds is difficult without viable vapor standards. Thus, we eliminate the requirement for vapor standards by combining the sensitivity of the instrumentation with a direct liquid deposition protocol to analyze trace explosive vapor samples.

Continuous flow, explosives vapor generator and sensor chamber.

A novel liquid injection vapor generator (LIVG) is demonstrated that is amenable to low vapor pressure explosives, 2,4,6-trinitrotoluene and hexahydro-1,3,5-trinitro-1,3,5-triazine. The LIVG operates in a continuous manner, providing a constant and stable vapor output over a period of days and whose concentration can be extended over as much as three orders of magnitude. In addition, a large test atmosphere chamber attached to the LIVG is described, which enables the generation of a stable test atmosphere with controllable humidity and temperature. The size of the chamber allows for the complete insertion of testing instruments or arrays of materials into a uniform test atmosphere, and various electrical feedthroughs, insertion ports, and sealed doors permit simple and effective access to the sample chamber and its vapor.